This is the Touchescreen user Interface.
WattStopper ELCU-200 EMERGENCY LIGHTING CONTROL UNIT. WattStopper’s ELCU-200 Emergency Lighting Control Unit is a self-contained device that allows any standard lighting control device to control emergency lighting in conjunction with normal
lighting in any area within a building. The ELCU-200 monitors a single circuit that provides normal lighting to an area. As long as
normal power is present, the ELCU-200 permits lighting control devices (e.g., occupancy sensors, panels, dimmers, or wall switches) to control the emergency lighting fixtures as well as the general lighting. If power is lost for any reason, including the tripping of a single branch circuit breaker, the ELCU-200 will force on the emergency fixtures for that area. The ELCU-200 can be wired either as a control device, so that emergency lighting follows
the control of normal lighting, or as a bypass device to shunt emergency power around a control device (e.g., a dimmer) when normal power fails.
Features
• Eliminates energy waste caused by emergency lighting that is always on
• Integral push-to-test button activates emergency mode for a true test condition
• Connects to EMTS-100 Remote Test Switch or other input to activate emergency on from a remote location
• Operates as a control device or as a shunt
• Senses local single circuit power failure
• Zero cross switching technology for reliability and increased product life
• Compatible with WattStopper occupancy sensors, daylighting controls, lighting control panels, and dimmers
• LED indication for emergency and normal power
• Half-second delayed on positively identifies emergency fixtures for required maintenance
• Provides absolute fail-to-on emergency lighting
• UL924 listed, meets NEC, OSHA and NFPA safety codes; UL2043 plenum rated
• Qualifies for use on ARRA-funded projects
Specifications
• 120/277 VAC; 60Hz
• Maximum load:
– Ballast 20 A @ 120/277 VAC
– Incandescent 10 A @ 120 VAC
– Motor 1HP @ 120 VAC
• Remote activation: supplies 24 VDC source for dry contact closure
• Integral control: push-to-test button on unit
• Housing: fire rated V-0, 176° F (80°C)
• Operating temperature range: 32 to 131°F (0 to 55°C)
• Relative humidity range: 5 to 95%, noncondensing
• Dimensions: 1.7” x 2.97” x 1.64” (43.2mm x 75.4mm x 41.7mm) H x W x D with a 1/2“ (12.7mm) threaded nipple
• UL, cUL listed Emergency Lighting and Power Equipment; five year warranty
For other items like the WattStopper ELCU-200 EMERGENCY LIGHTING CONTROL UNIT click here.
For more information on WattStopper’s line of lighting control solutions click here.
This is the wireless handheld configuration tool. Installers and end users can use the FSIR-100 for initial setup and subsequent sensor adjustment to ensure conformity with design intent. It simplifies changes to sensor settings by making the adjustment process ladder-free. It is compatible with IR-enabled Wattstopper HBP and FSP sensors. These products are ideal for use in parking facilities, gas station, pedestrian pathways and warehouse. Check out Wattstopper DLM products here.
This is the Isolé power strip w/ personal sensor. The Isolé IDP-3050 is an energy-saving control system that provides maximum surge and noise suppression while keeping plug load equipment off when there is no occupancy. It consists of an eight-outlet power strip and a personal occupancy sensor.
The IDP-3050 turns plug load devices on and off based on occupancy. The personal sensor connects to the eight-outlet power strip with the attached cable. The power strip contains six outlets controlled by occupancy and two outlets that are uncontrolled. The IDP-3050 automatically turns all controlled devices on when the workspace is occupied, and off when the workspace has been unoccupied for the user-defined time delay. Uncontrolled devices remain on regardless of occupancy. Check out Wattstopper DLM products here.
WattStopper LMCT-100-2 DIGITAL WIRELESS CONFIGURATION TOOL. The LMCT-100-2 Wireless Configuration Tool is a handheld tool for advanced remote configuration of any Wattstopper Digital Lighting Management (DLM) system. The tool enables system and device modifications via pushbutton, without ladders or tools, as well as easy duplication of settings between DLM local networks.
Powered by three AAA batteries, the LMCT-100-2 features an
easy-to-read organic LED (OLED) screen and bi-directional
communication with IR-enabled DLM devices. Its intuitive
navigation pad provides a familiar interface for users who can
see the current system parameters of a DLM local network and
make changes by navigating through simple menus. Adjustable
occupancy sensor parameters include sensitivity, time delay
and trigger modes. Load parameter settings (also referred to
as Push n’ Learn™) include blink warning, Auto- or Manualon mode, and re-assigning specific loads to different sensors.
Button configuration options include type (load or scene), mode,
fade times and scene lock. Dimming parameters include low/
high trim, preset level and lamp burn in time. Daylighting
adjustments include operating mode, setpoints, fade times and
time delays. The LMCT is also used to adjust the light level of
dimmed loads. As new DLM products are released, a microUSB port allows for easy firmware updates via software
Features
• Remotely reconfigures and reports DLM occupancy sensor
parameters: PIR and ultrasonic sensitivity; time delay; walk through mode; trigger mode (for dual technology sensors)
• Remotely reconfigures and reports DLM dimming
parameters: load type (dim/switch); low/high trim; preset on
level; lamp burn-in
• Manually adjusts light level of dimmed loads to facilitate scene setting
• Remotely configures, reconfigures and reports DLM photosensor settings: light levels; operating mode (on/off, bi-level, tri-level, dimming); setpoints; time delays; fade times; test mode
• Micro-USB port provided for firmware updates, allowing easy
updates for support of new DLM products
• The product meets the materials restrictions of RoHS
Specifications
Three AAA 1.5 volt batteries (included)
• OLED display 1.4”W x .75”H (36mm x 19mm)
• Infrared (IR) transceiver (36kHz frequency)
• IR range: up to 32’ (10m)
• Mcro-USB port for firmware updating
• Includes carrying case with belt clip
• Operating temperature: 32-104°F (0-40°C)
• FCC part 15 compliant
• Five year warranty
For other items like the WattStopper LMCT-100-2 DIGITAL WIRELESS CONFIGURATION TOOL click here.
For more information on WattStopper’s line of lighting control solutions click here.
WattStopper LMIO-101 INPUT/OUTPUT INTERFACE. The LMIO-101 Input/Output Interface allows seamless integration with third party devices to provide additional functionality in a Digital Lighting Management (DLM) system. The LMIO-101 operates on power from the DLM local network. It contains a 24VDC isolated relay (single-pole, double throw with normally open (N/O), normally closed (N/C), and common outputs) for output to other systems. The isolated relay can
respond to any DLM occupancy sensor on the DLM local network. The LMIO-101 also includes a 24VDC output and four input terminals for maintained or momentary switch closure inputs, or third party logic inputs. Input signals may come from a wide variety of devices including building automation systems, time clocks and key switches, for purposes including hold-on/ hold-off, load shedding and cleaning. The LMIO-101 has DIP switch-selectable profiles to allow different combinations of
input signals to control different loads.
Features
• Plug n’ Go™ configuration for quick and easy startup out of the box
• Push n’ Learn™ functionality for personalizing system
settings to accommodate application needs
• Self-contained switching power supply and relay system
• Five status LEDs and configuration LED
• Hold-on/hold-off, occupancy sensor, time clock, load shed, cleaning switch and key switch modes available through DIP switch configurations
• Over-current protection
• UL 2043 plenum rated
• The product meets the materials restrictions of RoHS
• BAA/TAA-compliant models available
Specifications
Input/output voltage: 24VDC from DLM network
• Maximum current consumption: 20mA
• DLM local network connection: 2 RJ45 ports
• Removable terminal block for connections to isolated relay output and third party inputs
• Isolated relay ratings:
– 24VDC/VAC, 1A, SPDT
– Normally open (N/O), normally closed (N/C) and common outputs
– Duplicates the functionality of the LMRL-100
• Input ratings:
– Input max. sink/source current: 1- 5 mA
– Logic input signal voltage High: >18 VDC
– Logic input signal voltage Low: < 2 VDC
• Operating conditions; for indoor use only; 32-131°F (0-55°C)
• Fits inside 4” x 4” j-box, 1 gang back box or 3” octagonal box; optional DIN rail mounting
• UL and cUL listed
• Five year warranty
For other items like the WattStopper LMIO-101 INPUT/OUTPUT INTERFACE click here.
For more information on WattStopper’s line of lighting control solutions click here.
WattStopper LMIO-102 PARTITION INTERFACE. The LMIO-102 Partition Interface automatically coordinates lighting controls in flexible spaces with up to four movable walls equipped with contact closures. It is part of a Digital Lighting Management (DLM) system, and can reconfigure connected switches and occupancy sensors.
Features
• Push n’ Learn™ functionality for personalizing system settings to accommodate application needs
• Four status LEDs indicate if walls are open or closed
• Two RJ45 ports with hinged dust cover
• UL 2043 plenum rated
• The product meets the materials restrictions of RoHS
• BAA/TAA-compliant models available
Specifications
• Input voltage: 24VDC from DLM local network
• Current consumption: 20mA
• DLM local network connection: 2 RJ45 ports
• Removable terminal block for connections to third party contact closure inputs
• Input ratings:
– Input max. sink/source current: 1- 5 mA
– Logic input signal voltage High: >18 VDC
– Logic input signal voltage Low: < 2 VDC
• Operating conditions: for indoor use only; 32-104°F (0-40°C)
• Fits inside 4” x 4” j-box, 1 gang back box or 3” or 4” octagonal box; optional DIN rail mounting
• UL and cUL listed
• Five year warranty
For other items like the WattStopper LMIO-102 PARTITION INTERFACE click here.
For more information on WattStopper’s line of lighting control solutions click here.
This is the plug load controller. LMPL-201 Plug Load Controllers include a 20-amp relay for on/ off control of connected outlets, and a high-efficiency switching power supply. They are part of a Wattstopper Digital Lighting Management (DLM) system, and enable energy-efficient control of plug loads. Check out Wattstopper DLM products here.
FEATURES:
WattStopper LMPW-100 PIR WALL SWITCH OCCUPANCY SENSORS. LMPW-100 Series PIR Wall Switch Occupancy Sensors use passive infrared (PIR) technology to detect occupancy for energy-efficient control of lighting and plug loads. They also include one or two switch buttons for manual control of selected loads, and are part of a Wattstopper Digital Lighting Management (DLM) system.
Features
• Plug n’ Go™ automatic configuration for quick installation and maximum energy savings
• Push n’ Learn™ functionality for customization without the need for tools or a PC
• Infrared (IR) transceiver for wireless configuration and control
• Sleek single gang devices fit decorator wall plates; 1- and 2-button models; six color options
• Sensors may be used for multi-way control
• Each switch button can control individual or multiple loads, or one scene; LED indicates status
• Each switch button can be used to raise or lower load levels
• Detection Signature Processing eliminates false triggers and provides immunity to RFI and EMI
• Sensor coverage tested to NEMA Guide Publication WD 7-2000
• The product meets the materials restrictions of RoHS
Specifications
• Input voltage: 24VDC from DLM network
• Current consumption: 8mA
• DLM local network connection: 2 RJ45 ports
• 1 or 2 switch buttons, each with LED status indicator
• Scrolling LCD display and pushbuttons for setting sensor and system parameters
• Infrared (IR) transceiver
• Operating conditions: for indoor use only; 32-131°F (0-55°C); 5-95% RH, non-condensing
• UL and cUL listed
• FCC part 15 compliant
• Five year warranty
For other items like the WattStopper LMPW-100 PIR WALL SWITCH OCCUPANCY SENSORS click here.
For more information on WattStopper’s line of lighting control solutions click here.
WattStopper LMRC-100 SERIES DIGITAL SWITCHING ROOM CONTROLLER. LMRC-100 Series Digital Room Controllers include one or two relay(s) for on/off control of a total of 20 amps, and a high-efficiency switching power supply. They are the foundation of a WattStopper Digital Lighting Management (DLM) system, and allow integration of occupancy sensors, daylighting
sensors and switches for energy-efficient lighting control. LMRC-100 Series Room Controllers operate on one 120 or 277 volt, 20 amp, feed and provide Class 2 power to sensors and switches via the DLM local network. Once powered up, Plug n’ Go automatically configures system components for the most energy-efficient operation. The room controllers then switch lighting or motor loads on and off in response to input from the communicating devices. The DLM system may be reconfigured using Push n’ Learn without the need for tools or a PC.
Features
• Plug n’ Go™ automatic configuration for quick installation and maximum energy savings
• Push n’ Learn™ functionality for personalization without the need for tools or a PC
• Digital Lighting Management components plug together on a free-topology Cat 5e DLM local network
• On/Off button for each load
• 3 RJ45 ports with integral strain relief and hinged dust cover
• Zero-crossing circuitry for each relay for reliability and increased product life
• Attach to standard electrical box through ½” knockout; UL2043 plenum rated
• RoHS compliant
Specifications
• Input/ouput voltage: 120/277VAC, 50/60Hz
• Maximum 20A combined load per Room
Controller; each relay rated for:
– Ballast or incandescent: 20A
– Motor load: 1Hp
• Class 2 output to DLM local network: 24VDC, 150mA across 3 RJ45 ports
• DLM local network parameters with LMRC-100 Series and/or LMPL-101 Room Controllers only:
– Maximum current: 600mA
– Category 5e cable, up to 1,000’
– Maximum of 4 room controllers, controlling up to 8 loads
– Up to 24 communicating devices
• Operating conditions: for indoor use only; 32-104°F (0-40°C); 5-95% RH, non-condensing
• UL and cUL listed
• FCC part 15 compliant
• Five-year warranty
For other items like the WattStopper LMRC-100 SERIES DIGITAL SWITCHING ROOM CONTROLLER click here.
For more information on WattStopper’s line of lighting control solutions click here.
WattStopper LMRC-110 SERIES 0-10V DIMMING ROOM CONTROLLERS (LMRC-111, LMRC-112). LMRC-110 series room controllers include one or two relay(s) to switch a total of 10 amps, a high-efficiency switching power supply and dual 0-10 volt outputs per relay for control of dimmable loads including compatible LED drivers or electronic ballasts. They are the foundation of a Digital Lighting Management (DLM) system, and allow integration of occupancy sensors, daylighting controls and switches for energy-efficient control.
LMRC-110 series room controllers operate on one 120 or 277
volt, 10 amp feed and provide Class 2 power to sensors and
switches via the DLM local network. Once powered up, Plug n’
Go automatically configures system components for the most
energy-efficient operation. The room controllers then dim or
switch lighting or motor loads in response to input from the
communicating devices. When a dimming input is received, the
relay switches on when the dimmed level rises above zero, and
off when it reaches zero, to coordinate control of power and the
0-10 volt signal to the load. They also monitor the current draw
of the total connected load. Each room controller stores up to
16 scene preset levels for each dimmed output.
Features
• Push n’ Learn™ functionality for personalization without the need for tools or a PC
• Digital Lighting Management components plug together on a free-topology Cat 5e DLM local network eliminatingwiring errors
• On/Off/Dim local override button for each load
• LED indicates status of each load
• Optional lamp burn in; 12 or 100 hours
• Optional instantaneous current and voltage measurement of total connected load
• 2 RJ45 ports; molded cable tie ring for strain relief
• Zero-crossing circuitry for each relay for reliability and increased product life
• UL 2043 plenum rated
• This product meets the materials restrictions of RoHS
• U.S.-made models available for public works projects
Specifications
• Voltage: 120/277VAC; 50/60Hz
• Maximum 10A combined load per Room Controller; each relay rated for 10A ballast, E-ballast or incandescent
• Galvanically isolated Class 1 pigtails and Class 2 terminals for 0-10VDC signal; sinks up to 50mA per output (Class 1/
Class 2) per channel for control of compatible ballasts (25 if each sources 2mA)
• Intelligently controlled Class 2 output to DLM local network: 24VDC, up to 150mA across 2 RJ45 ports
• DLM local network parameters:
– Maximum current: 800mA
– Category 5e cable: 150’ per device to 1,000’ max.
– Up to 64 loads
– Up to 48 communicating devices
– Maximum 4 LMPB-100, LMPL-101 or LMRC-100 Series Room Controllers
• Requires LMCS 4.5.1, Segment Manager 2.1.23, or LMCT 5.24
(or later)
• Operating conditions: for indoor use only; @120/277V:
32-131°F (0-55°C); 5-95% RH, non-condensing
• UL and cUL listed (E101196)
• FCC part 15 compliant
• Five year warranty
For other items like the WattStopper LMRC-110 SERIES 0-10V DIMMING ROOM CONTROLLERS click here.
For more information on WattStopper’s line of lighting control solutions click here.
WattStopper LMRH-101 DIMMING IR REMOTE CONTROL. The LMRH-101 Dimming IR Remote Control is a handheld personal control device for convenient on/off and raise/lower control of any load(s) connected to Digital Lighting Management (DLM) dimming room controllers. It uses an infrared transceiver to communicate with a DLM system via any DLM IR-enabled devices. The LMRH-101 operates on battery power. By default, it controls all loads on the DLM local network. The load assignment may be quickly reconfigured using Push n’ Learn.
To turn the load on, the user simply presses the top of the control button. Pressing the bottom of the button turns lights off. To raise or lower dimmable loads, the user presses and holds the top or bottom of the button until lighting reaches the desired level. The LMRH-101 will work with any DLM local network, operating all loads if in default mode, or the load(s) it has been configured to control.
Features
• Provides remote IR dimming control of lighting in a DLM system in conjunction with at least one dimming room controller
• Hidden configuration button for easy access to Push n’ Learn
• Communicates with DLM local network through any DLM
IR-enabled device
• Battery operated
• Includes wall mount holster and all necessary mounting hardware
• Can control one or more loads
• LED confirms button presses
• The product meets the materials restrictions of RoHS
Specifications
Operates on 3 AAA 1.5 volt batteries (included)
• DLM local network connection: IR transceiver
– Range of IR transmission: up to 32 ft. (10m)
– Angle of IR reception: 30°
• 1 control button with LED indicator
• Hidden configuration button to access Push n’ Learn
• Weight: approx. 3.2 oz. (91g), without mounting bracket
• Operating conditions: for indoor use only; 32-95°F (0-35°C); 5-95% RH, non-condensing
• FCC part 15 compliant
• Five year warranty
For other items like the WattStopper LMRH-101 DIMMING IR REMOTE CONTROL click here.
For more information on WattStopper’s line of lighting control solutions click here.