• Intelligent, continually adapting ultrasonic sensor
• Excellent minor motion sensitivity
• Non-Volatile Memory: settings saved in protected memory are not lost during power outages

• Intelligent, continually adapting ultrasonic sensor
• Excellent minor motion sensitivity
• Non-Volatile Memory: settings saved in protected memory are not lost during power outages

• Auto-On Low-Light feature will turn lights on automatically only if there is less than approximately 10 Lux (1 fc) of ambient light
• Passive infrared motion detection with exclusive Lutron XCT TM Technology for fine motion detection
• Simple adjustments available for Timeout, Auto-On, and Activity settings
• Supports advanced occupancy features, such as dependent occupancy groups and customizable occupied/unoccupied presets in some systems
• Multiple sensors can be added for extended coverage
• Lens illuminates during test mode to verify ideal locations

Lutron® Radio Powr SavrTM occupancy/vacancy sensors are wireless, battery-powered, passive infrared (PIR) sensors that automatically control lights via RF communication to compatible dimming and switching devices.

This is a Vive Basic Package 8 Amp Radio Powr Savr Switch & Ceiling Sensor. The Maestro Wireless solution incorporates Maestro Wireless load controls, wireless sensors, and wireless remote controls, which provide a system that delivers energy savings, convenience, and ease of installation. Maestro Wireless dimmers and switches use Lutron patented Clear Connect RF Technology, which enables wireless communication with Radio Powr Savr sensors and Pico remote controls for light control and general switched loads. These products are also compatible with the Vive hub which enables a simple setup process using a standard web browser on any Wi-Fi enabled phone, tablet or computer. It also enables control and monitoring of all Vive devices. The Vive hub can be added at any time and preserves existing system setup by extracting local programming from each device. For a complete list of features supported with the Vive hub, call Lite Rite Controls. Note for Replacement: MRF2S – the “S” model can replace the non-”S” model. Click here to see the Lutron Vive story.

Features:

• The Vive Basic Package 8 Amp Radio Powr Savr Switch & Ceiling Sensor.
• Lutron® patented Clear Connect® RF Technology works through walls and floors.
• Controls include Front Accessible Service Switch (FASS™) for safe lamp replacement.
• Two-wire installation for any retrofit application.
• Power failure memory: If power is interrupted, the control will return to its previously set level prior to interruption.

This is a Vive basic package 8 Amp switch & hallway sensor. The Maestro Wireless solution incorporates Maestro Wireless load controls, wireless sensors, and wireless remote controls, which provide a system that delivers energy savings, convenience, and ease of installation. Maestro Wireless dimmers and switches use Lutron patented Clear Connect RF Technology, which enables wireless communication with Radio Powr Savr sensors and Pico remote controls for light control and general switched loads. These products are also compatible with the Vive hub which enables a simple setup process using a standard web browser on any Wi-Fi enabled phone, tablet or computer. It also enables control and monitoring of all Vive devices. The Vive hub can be added at any time and preserves existing system setup by extracting local programming from each device. For a complete list of features supported with the Vive hub, call Lite Rite Controls. Note for Replacement: MRF2S – the “S” model can replace the non-”S” model. Click here to see the Lutron Vive story.

HIGHLIGHTS:

• The Vive basic package 8 Amp switch & hallway sensor provides switching and occupancy / vacancy sensing.
• Lutron patented Clear Connect RF Technology works through walls and floors.
• Controls include Front Accessible Service Switch (FASSTM) for safe lamp replacement.
• Two-wire installation for any retrofit application.
• Power failure memory: If power is interrupted, the control will return to its previously set level prior to interruption.

System Communications and Capacity

• Maestro Wireless controls communicate with the Pico remote controls and Radio Power Savr
• sensors through radio frequency (RF).
• Receives wireless inputs from up to 10 Pico remote controls, 10 Radio Powr Savr occupancy / vacancy sensors, and 1 Radio Powr Savr daylight sensor
• Maestro Wireless local controls must be located within 60 ft. (18 m) line of sight or 30 ft. (9 m) through walls, of Radio Power Savr sensors.
• Maestro Wireless local controls must be located within 60 ft. (18 m) line of sight or 30 ft. (9 m)
• through walls, of a Pico remote control.
• Up to 10 Maestro Wireless controls can be configured to work together.
• Sensors can be assigned to multiple switches.

This is a Vive basic Package: Switch & Ceiling Vacancy Sensor. The Maestro Wireless solution incorporates Maestro Wireless load controls, wireless sensors, and wireless remote controls, which provide a system that delivers energy savings, convenience, and ease of installation. Maestro Wireless dimmers and switches use Lutron patented Clear Connect RF Technology, which enables wireless communication with Radio Powr Savr sensors and Pico remote controls for light control and general switched loads. These products are also compatible with the Vive hub which enables a simple setup process using a standard web browser on any Wi-Fi enabled phone, tablet or computer. It also enables control and monitoring of all Vive devices. The Vive hub can be added at any time and preserves existing system setup by extracting local programming from each device. For a complete list of features supported with the Vive hub, call Lite Rite Controls

The Vive™ Basic Package incorporates Maestro® load controls and wireless sensors which provides a system that delivers energy savings, convenience and ease of installation. These products are also compatible with the Vive™ hub which enables a simple setup process using a standard web browser on any Wi-Fi enabled phone, tablet or computer. It also enables control and monitoring of all Vive™ devices. The Vive™ hub can be added at any time and preserves existing system setup by extracting local programming from each device. Click here to see the Lutron Vive story.

Features:

• The Vive™ Basic package provides switching and occupancy / vacancy sensing of multiple load types.
• Lutron® patented Clear Connect® RF Technology works through walls and floors.
• Controls include Front Accessible Service Switch (FASS™) for safe lamp replacement.
• Two-wire installation for any retrofit application.
• Power failure memory: If power is interrupted, the control will return to its previously set level prior to interruption.

This is the ultrasonic ceiling sensor. Wattstopper’s W Series Ultrasonic Ceiling Sensors are versatile motion detectors that control lighting in a wide variety of applications. W Series Sensors can be used individually or as part of an integrated system of Wattstopper lighting control products.

The 24 VDC W Series Sensors utilize advanced omni-directional, ultrasonic technology to sense occupancy. When movement is detected in a controlled area, the W Series Sensors will switch lights on via low-voltage wiring through to a Wattstopper power or auxiliary pack. Once the area is vacated and the user adjustable time delay (15 seconds to 15 minutes) has elapsed, lighting systems automatically switch off. Check out Wattstopper DLM products here.

This is the low voltage PIR ceiling sensor. Wattstopper’s CI-300 Passive Infrared (PIR) Ceiling Sensors automatically turn lighting on and off based on occupancy. The sensor mounts on the ceiling with a flat, low-profile appearance and provides 360 degrees of coverage.

CI-300 Series Sensors operate on 24 VDC, VAC or halfwave rectified. Utilizing the latest PIR technology, they automatically turn lighting on when a difference is detected between infrared energy from a human body in motion and the background space. When no occupancy is detected for the length of the time delay, lighting automatically turns off. For manual-on operation, the CI-300 will operate with a low-voltage momentary switch. Check out Wattstopper DLM products here.

360° up to 1200 ft2

This is the low voltage PIR ceiling sensor. Wattstopper’s CI-300 Passive Infrared (PIR) Ceiling Sensors automatically turn lighting on and off based on occupancy. The sensor mounts on the ceiling with a flat, low-profile appearance and provides 360 degrees of coverage.

CI-300 Series Sensors operate on 24 VDC, VAC or halfwave rectified. Utilizing the latest PIR technology, they automatically turn lighting on when a difference is detected between infrared energy from a human body in motion and the background space. When no occupancy is detected for the length of the time delay, lighting automatically turns off. For manual-on operation, the CI-300 will operate with a low-voltage momentary switch. Check out Wattstopper DLM products here.

360° up to 500 ft2

This is the wireless RF PIR occupancy sensor. The EOPC-100 Wireless RF PIR Occupancy Sensor works with EOSW-100 Series RF Wall Switches to turn lights on and off based on occupancy. The sensor mounts on the ceiling and provides 360° passive infrared coverage. EOPC-100 wireless sensors operate on power supplied by two photovoltaic panels capable of reaching a full charge in 6 hours when the ambient light level is 20 footcandles (215 lux). Each sensor can be paired with multiple loads controlled by RF wall switches. Paired loads configured for automatic-on operation turn on when a sensor transmits an RF signal that it has detected occupancy. As long as the sensor detects occupany it continues transmitting signals to the paired wall switch receivers. All paired loads turn off when no occupancy has been detected for the duration of the selected time delay. Check out Wattstopper DLM products here.

• Wireless RF occupancy sensors work with EOSW-100 Series RF wall switches
• Detection Signature Processing to eliminate false triggers and provide immunity to RFI and EMI
• Trimpot for sensitivity adjustment
• Test mode allows quick and easy set up
• Includes plate for mounting to single- or double-gang junction boxes or ceiling tile
• Reversible magnetic/adhesive disc for surface mounting
• Sensor coverage tested to NEMA Guide Publication WD 7-2000

WattStopper LMDC-100 DUAL TECHNOLOGY CEILING MOUNT OCCUPANCY SENSOR. The LMDC-100 low profile Dual Technology Ceiling Mount Occupancy Sensor uses both passive infrared (PIR) and ultrasonic technologies to achieve precise occupancy sensing for energy-efficient control of lighting and plug loads. It is a digital sensor, and is part of a Wattstopper Digital Lighting Management (DLM) system.

The LMDC-100 operates on Class 2 power supplied to a DLM
local network by one or more DLM room controllers. It works
with the room controller(s) to turn loads on and off based on
occupancy. Default operation is established by Plug n’ Go, which
automatically configures system components to maximize
energy savings. Initially, all occupancy sensors control all loads
on the same local network. Each LMDC-100 may be assigned
to a specific load; load assignments and load parameters
may be changed using Push n’ Learn. The LMDC-100 may be
reconfigured either using the pushbuttons and an LCD screen
conveniently located behind the snap-off front sensor cover, or
with a wireless configuration tool.

Features

Plug n’ Go™ automatic configuration for quick installation and maximum energy savings
• Push n’ Learn™ functionality for customization without the need for tools or a PC
• Digital Lighting Management components plug together on a
free-topology Category 5e DLM local network
• Infrared (IR) transceiver for wireless configuration and control
• Ultrasonic diffusion technology spreads coverage to a wider area (patented); 40KHz signal
• 360 degree PIR coverage
• Detection Signature Processing eliminates false triggers and
provides immunity to RFI and EMI
• The product meets the materials restrictions of RoHS
• Sensor coverage tested to NEMA Guide Publication WD 7-2000
• BAA/TAA-compliant models available

Specifications

• Plug n’ Go™ automatic configuration for quick installation and maximum energy savings
• Push n’ Learn™ functionality for customization without the need for tools or a PC
• Digital Lighting Management components plug together on a
free-topology Category 5e DLM local network
• Infrared (IR) transceiver for wireless configuration and control
• Ultrasonic diffusion technology spreads coverage to a wider area (patented); 40KHz signal
• 360 degree PIR coverage
• Detection Signature Processing eliminates false triggers and provides immunity to RFI and EMI
• The product meets the materials restrictions of RoHS
• Sensor coverage tested to NEMA Guide Publication WD 7-2000
• BAA/TAA-compliant models available

For other items like the WattStopper LMDC-100 DUAL TECHNOLOGY CEILING MOUNT OCCUPANCY SENSOR click here.

For more information on WattStopper’s line of lighting control solutions click here.