This is the PIR wall switch vacancy sensor. The CS-50 Passive Infrared (PIR) Vacancy Sensor provides automatic shutoff for single-pole lighting control applications. It is engineered to comply with specific provisions of California’s Title 24-2013 energy code. The CS-50 operates as a manual-on sensor. Users must press the pushbutton to turn on lighting. The CS-50 employs PIR technology to sense the difference between the infrared energy from a person in motion and the background space. It keeps lighting on as long as motion is detected and provides automatic shutoff, following a user-selected time delay, when motion is no longer detected. Users may turn the lighting off manually. The CS-50 is shipped preset for a 30 minute time delay, and does not require any adjustment after installation. If desired, the time delay may be easily reduced to 25, 20, 15, 10 or 5 minutes or to 30 seconds. The time delay should be set relative to the anticipated duration of stay and level of activity in the room; 30 minutes for guest room and executive restroom, and 5 to 10 minutes for pantries and laundry rooms. Check out Wattstopper DLM products here.

• Replaces single-pole switches
• Adjustable time delay, 30 seconds to 30 minutes
• If enabled, status indicator blinks when motion is detected
• Low-profile styling
• Choice of five decorator colors; lens is color-matched to device
• Operates most common types of lighting or fan motors
• Relay-based switching
• No current leakage to load in off mode for safety
• Compatible with decorator wall plates
• CA Title 24 compliant

This is the dual technology wall switch sensor w/ 2-relays. The DSW-200 dual technology wall switch sensor turns lights ON and OFF based on occupancy and contains two relays for controlling two independent lighting loads or circuits. It combines the benefits of passive infrared (PIR) and ultrasonic detection technologies for high sensitivity to small and large movements. The DSW-200 replaces existing wall switches and fits a standard decorator wall plate.

Each of the DSW-200’s relays can control a separate lighting load. By default, when the PIR sensor detects occupancy, relay 1 turns ON automatically. Detection by either PIR or ultrasonic technology holds lights ON. When occupancy is no longer detected and the time delay elapses, lights automatically turn OFF. Dual ON/OFF buttons allow the user to turn on and off each of the loads manually. DIP switch settings allow for a variety of control options such as Auto-ON or Manual-ON for each relay, walk-through, and test mode. Check out Wattstopper DLM products here.

This is the dual technology wall switch occupancy sensor. The DSW-301 dual technology wall switch sensor turns lights OFF and ON based on occupancy. It combines the benefits of passive infrared (PIR) and ultrasonic detection technologies. The DSW-301 replaces existing wall switches and fits behind a standard decorator wall plate. Once the lights are ON, detection by either technology holds lights ON until occupancy is no longer detected and the time delay elapses. Factory default operation is for Manual-ON, so that users must turn lights on. DIP switch settings allow for a variety of control options including Auto-ON operation, walk-through and test mode. In Auto-ON mode, the DSW-301 turns lighting on when the PIR sensor detects occupancy. Additional DIP switch settings allow the user to choose which sensing technologies hold ON or retrigger the lighting. Multiple sensors may be used for control of one or more loads from up to four locations. The DSW-301 sensor uses a patent pending Neutral Sense Technology. Any DSW-301 sensor can be used for a two-wire or three wire application, either to work with existing wiring, or to meet local or national code requirements. An easy-to-break plastic tab covers neutral screw terminals. Once the sensor is connected to neutral it complies with all codes that restrict current leakage to ground. Check out Wattstopper DLM products here.

• Complies with 2011 NEC requirements
• Zero-crossing for long relay life
• Vandal resistant lens combines precise coverage with durability
• Selectable walk-through mode turns lights off three minutes after initial occupancy if no motion is detected after the first 30 seconds
• Test mode allows quick and easy adjustments
• Selectable audible alert for impending shutoff
• In automatic mode, sensor returns automatically to Auto-ON after lights are turned off manually; ideal for presentations
• Four occupancy logic options to customize control to meet application needs
• Optional light level sensing with simple setup
• Service mode allows sensor to operate as a service switch in the unlikely event of a failure
• Sensor coverage tested to NEMA Guide Publication WD 7-2000

This is the dual technology dual relay wall switch occupancy sensor. The DSW-302 dual technology wall switch sensor turns lights ON and OFF based on occupancy and contains two relays for controlling two independent lighting loads or circuits. It combines the benefits of passive infrared (PIR) and ultrasonic detection technologies for high sensitivity to small and large movements. The DSW-302 replaces existing wall switches and fits a standard decorator wall plate. Each of the DSW-302’s relays can control a separate lighting load. By default, when the PIR sensor detects occupancy, relay 1 turns ON automatically. Remaining lighting must be turned on manually. Detection by either PIR or ultrasonic technology holds lights ON. When occupancy is no longer detected and the time delay elapses, lights automatically turn OFF. Dual ON/ OFF buttons allow the user to turn on and off each of the loads manually. DIP switch settings allow for a variety of control options such as Auto-ON or Manual-ON for each relay, walkthrough, and test mode. Multiple sensors may be used for control of one or more loads from up to four locations. The DSW-302 sensor uses a patent pending Neutral Sense Technology. Any DSW-302 sensor can be used for a two-wire or three wire application, either to work with existing wiring, or to meet local or national code requirements. An easy-to-break plastic tab covers neutral screw terminals. Once the sensor is connected to neutral it complies with all codes that restrict current leakage to ground. Check out Wattstopper DLM products here.

• Complies with 2011 NEC requirements
• Zero-crossing on both relays for long relay life
• Vandal resistant lens combines precise coverage with durability
• Selectable walk-through mode turns lights off three minutes after the room is initially occupied if no motion is detected after the first 30 seconds
• Selectable audible alert for impending shutoff
• In automatic mode, sensor returns automatically to Auto-ON after lights are turned off manually; ideal for presentations
• Test mode allows quick and easy adjustments
• Four occupancy logic options to customize control to meet application needs
• Optional light level sensor holds secondary lights off when ambient lighting is above the preset level
• Service mode allows sensor to operate as a service switch in the unlikely event of a failure
• Sensor coverage tested to NEMA Guide Publication WD 7-2000

This is the dual technology line voltage ceiling sensor. Wattstopper’s low profile DT-355 dual technology occupancy sensor combines the benefits of passive infrared (PIR) and ultrasonic technologies. The sensor mounts on the ceiling with a flat, unobtrusive appearance and provides 360 degrees of coverage.

The DT-355 is line voltage and operates on a single phase at 120, 230, 277 or 347 VAC. The sensor turns lighting on when both PIR and ultrasonic technologies detect occupancy. PIR technology senses the difference between infrared energy from a human body in motion and the background space. Ultrasonic technology uses high frequency (40kHz) ultrasound to sense motion within the space. Once lighting is on, detection by either technology holds lighting on. When no occupancy is detected for the length of the time delay, lighting turns off. The DT-355 can also be set so that only one technology is needed to trigger or both technologies are needed to hold lighting on. Check out Wattstopper DLM products here.

This is the sensor / switch installer kit. The EOPC-100 Wireless RF PIR Occupancy Sensor works with EOSW-100 Series RF Wall Switches to turn lights on and off based on occupancy. The sensor mounts on the ceiling and provides 360° passive infrared coverage. EOPC-100 wireless sensors operate on power supplied by two photovoltaic panels capable of reaching a full charge in 6 hours when the ambient light level is 20 footcandles (215 lux). Each sensor can be paired with multiple loads controlled by RF wall switches. Paired loads configured for automatic-on operation turn on when a sensor transmits an RF signal that it has detected occupancy. As long as the sensor detects occupany it continues transmitting signals to the paired wall switch receivers. All paired loads turn off when no occupancy has been detected for the duration of the selected time delay. Check out Wattstopper DLM products here.

• Wireless RF occupancy sensors work with EOSW-100 Series RF wall switches
• Detection Signature Processing to eliminate false triggers and provide immunity to RFI and EMI
• Trimpot for sensitivity adjustment
• Test mode allows quick and easy set up
• Includes plate for mounting to single- or double-gang junction boxes or ceiling tile
• Reversible magnetic/adhesive disc for surface mounting
• Sensor coverage tested to NEMA Guide Publication WD 7-2000

This is the outdoor motion sensor. Wattstopper’s EW outdoor motion sensors provide occupancy based control of outdoor lighting. Raintight and rated for -40°F to 130°F, EW sensors perform reliably in all weather conditions.

EW sensors operate at line voltage and can be mounted onto a standard, outdoor junction box. Utilizing advanced PIR technology, the sensors detect the difference between infrared energy in motion and the background space to turn lighting on when a person or vehicle enters the coverage area. After the area is vacated and the time delay elapses, lighting automatically turns off. The EW’s dual PIR detectors and three level lens increase the detection density as well as the accuracy of motion detection. Check out Wattstopper DLM products here.

• Sensors can be mounted on walls, eaves, or ceilings for installation convenience
• 270° coverage
• Front rotates for easy coverage adjustment
• Precision, double-shot tooling with internal silicon gaskets prevents water and dust contamination
• No tools needed to aim or adjust lamp holders for speedier installation
• Optional override-ON to turn lights on remotely for the length of the time delay
• ON/OFF control based on daylight levels via adjustable light level setting
• Zero crossing circuitry reduces stress on the relay and results in increased sensor life
• ASIC enhances reliability and helps to eliminate false triggers
• Pulse Count Processing eliminates false triggers and provide RFI and EMI immunity
• Patented Voltage Drop Protection
• Solid state digital microprocessor offers increased reliability
• User-adjustable time delay from 12 seconds to 16 minutes

Long, narrow PIR detection for control of hallway lighting.

• 100% Digital PIR detection
• Coverage up to 130 ft. (39.62m)
• Push button programmable
• Adjustable time delays
• Convenient test mode
• No field calibration or sensitivity adjustments required
• 100 hr. lamp burn-in timer
• Recommended Power Pack: PP20

This is the dual technology high bay occupancy sensor ceiling mount. The Lightcloud Sensor is a dual-technology motion detector that can switch and dim both local and remote circuits. It monitors power consumption, and can send an alert if power is lost. The Sensor is available for both standard and high bay applications, each with the option of surface or fixture mounting.

• Passive infrared motion detector with built-in fixture and zone control
• Occupancy and vacancy sensing with adjustable sensitivity and timeouts
• Switching for a fixture or entire zone, hard-wired or remote
• Supports 0-10V dimming for LED and fluorescent fixtures
• Easily set up schedules and scenes
• Power measurement and energy reporting
• Remote control from Lightcloud web application
• Communicates over secure wireless mesh network – no internet required

RAB Lighting creates high quality, affordable, well designed and energy efficient indoor and outdoor LED lighting, fixtures, sensors and controls. Check out the RAB Lighting Controls page.

This is the dual technology high bay occupancy sensor fixture mount. The Lightcloud Sensor is a dual-technology motion detector that can switch and dim both local and remote circuits. It monitors power consumption, and can send an alert if power is lost. The Sensor is available for both standard and high bay applications, each with the option of surface or fixture mounting.

• Passive infrared motion detector with built-in fixture and zone control
• Occupancy and vacancy sensing with adjustable sensitivity and timeouts
• Switching for a fixture or entire zone, hard-wired or remote
• Supports 0-10V dimming for LED and fluorescent fixtures
• Easily set up schedules and scenes
• Power measurement and energy reporting
• Remote control from Lightcloud web application
• Communicates over secure wireless mesh network – no internet required

RAB Lighting creates high quality, affordable, well designed and energy efficient indoor and outdoor LED lighting, fixtures, sensors and controls. Check out the RAB Lighting Controls page.

This is the dual technology high bay occupancy sensor fixture mount w/ height adjuster. The Lightcloud Sensor is a dual-technology motion detector that can switch and dim both local and remote circuits. It monitors power consumption, and can send an alert if power is lost. The Sensor is available for both standard and high bay applications, each with the option of surface or fixture mounting.

• Passive infrared motion detector with built-in fixture and zone control
• Occupancy and vacancy sensing with adjustable sensitivity and timeouts
• Switching for a fixture or entire zone, hard-wired or remote
• Supports 0-10V dimming for LED and fluorescent fixtures
• Easily set up schedules and scenes
• Power measurement and energy reporting
• Remote control from Lightcloud web application
• Communicates over secure wireless mesh network – no internet required

RAB Lighting creates high quality, affordable, well designed and energy efficient indoor and outdoor LED lighting, fixtures, sensors and controls. Check out the RAB Lighting Controls page.

This is the dual technology lightcloud sensor ceiling mount. The Lightcloud Sensor is a dual-technology motion detector that can switch and dim both local and remote circuits. It monitors power consumption, and can send an alert if power is lost. The Sensor is available for both standard and high bay applications, each with the option of surface or fixture mounting.

• Passive infrared motion detector with built-in fixture and zone control
• Occupancy and vacancy sensing with adjustable sensitivity and timeouts
• Switching for a fixture or entire zone, hard-wired or remote
• Supports 0-10V dimming for LED and fluorescent fixtures
• Easily set up schedules and scenes
• Power measurement and energy reporting
• Remote control from Lightcloud web application
• Communicates over secure wireless mesh network – no internet required

RAB Lighting creates high quality, affordable, well designed and energy efficient indoor and outdoor LED lighting, fixtures, sensors and controls. Check out the RAB Lighting Controls page.