WattStopper RD-200-W PASSIVE INFRARED (PIR) DIMMING WALL SWITCH VACANCY SENSOR. This is the Passive Infrared (PIR) Dimming Wall Switch Vacancy Sensor. The RD-200 PIR Dimming Wall Switch Vacancy Sensor provides preset dimming control and occupancy-based automatic lighting shutoff for applications throughout the home. The RD-200 can dim incandescent loads from a minimum level of 10% to a maximum level of 100%. When the pushbutton is pressed and held, the RD-200 will ramp the lights up and down in a continuous cycle until the pushbutton is released. The dimming direction may be reversed by momentarily releasing the pushbutton and then pressing it again.

• Replaces standard single pole switch or incandescent dimmer
• Low-profile styling
• Choice of four decorator colors; lens is color matched to device
• Includes matching single-gang wall plate
• Lighted pushbutton for visibility in darkened rooms
• Manual-on or automatic-on operation
• Adjustable time delay from 15 seconds to 30 minutes
• Soft start technology to prolong lamp life
• Air gap isolation switch for safe re-lamping
• If enabled, light level sensing prevents automatic-on when adequate daylight exists

For other items like the WattStopper RD-200-W PASSIVE INFRARED (PIR) DIMMING WALL SWITCH VACANCY SENSOR click here.

For more information on Wattstopper’s line of lighting solutions click here.

CHECK OUT THIS CASE STUDY

WS-CaseStudy-GreenHome_OccupancyVacancyTimeswitches

WattStopper WRC-15/20 AMP WIRELESS RECEPTACLE CONTROL. Wireless Receptacle Control products facilitate Auto-On/AutoOff occupancy-based control of plug loads without the need to wire receptacles to power packs. A WRC transmitter works with WRC RF-enabled relay-controlled receptacles.

The 24VDC WRC-TX is wired to an occupancy sensor and a power pack to transmit On/Off signals to bound receptacles. A relay in each WRC receptacle switches the controlled outlet(s)
in response to the transmission. One transmitter can be bound
to up to 16 WRC receptacles, each with one or two controlled
outlets. In addition, each WRC receptacle has feed thru capability for downstream control of additional outlets.

Features

RF Transmitter (WRC-TX)
• Works with all 24VDC Wattstopper occupancy sensors and power packs
• Two mounting options for convenient installation in acoustic tile or to other surfaces
• Operates in quiet 915 MHz band to avoid interference
• LED indicator communicates status during binding
• The product meets the materials restrictions of RoHS RF

Receptacles (WRC Series)
• Choice of 15A or 20A rating
• Duplex receptacles with a choice of one or two controlled outlets
• Labeling meets NEMA requirements for controlled receptacles
• LED indicator communicates status during binding
• The product meets the materials restrictions of RoHS

Specifications

RF Transmitter
• Operating voltage: 24VDC
• Current consumption: 3mA
• Mounts to acoustic tile or other surface via keyhole mounting
• FCC Part 15 compliant Controlled Receptacles
• Operating voltage: 125VAC
• Load rating: 15A (WRC-15) or 20A (WRC-20)
• Auto ground strap construction
• Terminals for power feed-thru

RF System (Transmitter and Receptacles)
• NEMA-approved labeling for controlled receptacles
• Frequency: 915 MHz band
• Communication range: 30’ in obstructed application; up to 150’ with clear line of sight
• One transmitter can bind to up to 16 controlled duplex receptacles
• Operating conditions; for indoor use only
• UL and cUL listed
• Five year warranty

For other items like the WattStopper WRC-15/20 AMP WIRELESS RECEPTACLE CONTROL click here.

For more information on WattStopper’s line of lighting control solutions click here.

Wattstopper WS-250 PIR WALL SWITCH OCC SENSOR. This is the passive infrared wall switch occupancy sensor. The WS-250 Passive Infrared (PIR) Wall Switch Sensor turns lighting on and off based on occupancy and ambient light level. It replaces existing wall switches and fits behind a standard decorator wall plate.

The WS-250 utilizes advanced PIR technology to detect occupancy. Detection occurs when the WS-250 senses the difference between infrared energy from a human body in motion and the background space. Lighting automatically turns on when occupancy is detected. After a user-specified length of time when no occupancy is detected, lighting automatically switches off. The sensor can also be used with line voltage switches for multi-level lighting.

Features

• Pulse Count Processing eliminates false offs without
reducing sensitivity
• Detection Signature Processing eliminates false triggers;
provides immunity to RFI and EMI
• Zero crossing circuitry reduces stress on the relay and
results in increased sensor life
• Time delay adjustment from 30 seconds up to 30 minutes
• Adjustable unit sensitivity from 20% to 100%
• Light level sensor holds lights off when ambient lighting is
above the preset level
• Custom two-tier Fresnel lens enhances detection at the
desktop level
• Sensor coverage tested to NEMA Guide Publication WD 7-2000
• Patented voltage drop protection
• For safety, there is no leakage to load in the off mode and
sensor is safety grounded
• LED indicates occupancy detection
• Compatible with decorator wall plates
• BAA/TAA-compliant models available

For other items like the Wattstopper WS-250 PIR WALL SWITCH OCC SENSOR click here.

For more information on Wattstopper’s line of lighting solutions click here.

This is the passive infrared wall switch occupancy sensor. The WS-301 Passive Infrared (PIR) Wall Switch Sensor turns lighting or fan loads on and off based on occupancy and ambient light level. The sensor replaces existing wall switches and fits behind a standard decorator wall plate.

The WS-301 senses the difference between infrared energy from a human body in motion and the background space to turn on lighting automatically when occupancy is detected. After a user-specified length of time when no occupancy is detected, lighting automatically switches off. The sensor can also be used with line voltage switches for multi-level lighting. Check out Wattstopper DLM products here.

• Complies with 2011 NEC requirements
• Zero crossing circuitry reduces stress on the relay and results in increased sensor life
• Adjustable time delay and sensitivity
• Custom two-tier Fresnel lens enhances detection at the desktop level
• Sensor coverage tested to NEMA Guide Publication WD 7-2000
• Light level sensor holds lights off when ambient lighting is above the preset level
• Patented voltage drop protection
• For safety, there is no leakage to load in the off mode and sensor is safety grounded
• LED indicates occupancy detection

• Auto-On
• PIR Coverage (Passive Infrared)
• Small Motion Detection up to 20 ft, Large Motion Detection up to 36 Ft
• Push-Button Programmable w/o Removing the Switch Plate
• Adjustable Time Delay
• Compatible w/ Electronic & Magnetic Ballasts, CFLs, LEDs, & Incandescents
• Self-Grounding Mounting Strap
• Interchangeable Hot & Load Wires
• No Neutral Required
• No Minimum Load Requirements

• Auto-On
• Dual Relay
• PIR Coverage (Passive Infrared)
• Small Motion Detection up to 20 ft, Large Motion Detection up to 36 Ft
• Push-Button Programmable w/o Removing the Switch Plate
• Adjustable Time Delay
• Compatible w/ Electronic & Magnetic Ballasts, CFLs, LEDs, & Incandescents
• Self-Grounding Mounting Strap
• Interchangeable Hot & Load Wires
• No Neutral Required
• No Minimum Load Requirements

• Auto or Manual On
• Dual Relay
• PIR Coverage (Passive Infrared)
• Small Motion Detection up to 20 ft, Large Motion Detection up to 36 Ft
• Push-Button Programmable w/o Removing the Switch Plate
• Adjustable Time Delay
• Compatible w/ Electronic & Magnetic Ballasts, CFLs, LEDs, & Incandescents
• Self-Grounding Mounting Strap
• Interchangeable Hot & Load Wires
• No Neutral Required
• No Minimum Load Requirements

• PDT (Passive Dual Technology) option (also called Microphonics) provide overlapping detection of human activity over the complete PIR coverage area.
• Auto-On
• PDT (Passive Dual Technology) option (also called Microphonics) provide overlapping detection of human activity over the complete PIR coverage area.
• Small Motion Detection up to 20 ft, Large Motion Detection up to 36 Ft
• Push-Button Programmable w/o Removing the Switch Plate
• Adjustable Time Delay
• Compatible w/ Electronic & Magnetic Ballasts, CFLs, LEDs, & Incandescents
• Self-Grounding Mounting Strap
• Interchangeable Hot & Load Wires
• No Neutral Required
• No Minimum Load Requirements
• Applications: Restrooms, Small Offices, Small Spaces, Closets

• Auto-On
• Dual Relay
• Dual technology (PDT) utilizes PIR/Microphonics detection
• Small Motion Detection up to 20 ft, Large Motion Detection up to 36 Ft
• Push-Button Programmable w/o Removing the Switch Plate
• Adjustable Time Delay
• Compatible w/ Electronic & Magnetic Ballasts, CFLs, LEDs, & Incandescents
• Self-Grounding Mounting Strap
• Interchangeable Hot & Load Wires
• No Neutral Required
• No Minimum Load Requirements

• Auto or Manual On
• Dual Relay
• Dual technology (PDT) utilizes PIR/Microphonics detection
• Small Motion Detection up to 20 ft, Large Motion Detection up to 36 Ft
• Push-Button Programmable w/o Removing the Switch Plate
• Adjustable Time Delay
• Compatible w/ Electronic & Magnetic Ballasts, CFLs, LEDs, & Incandescents
• Self-Grounding Mounting Strap
• Interchangeable Hot & Load Wires
• No Neutral Required
• No Minimum Load Requirements

• Manual On
• Dual technology (PDT) utilizes PIR/Microphonics detection
• Small Motion Detection up to 20 ft, Large Motion Detection up to 36 Ft
• Push-Button Programmable w/o Removing the Switch Plate
• Adjustable Time Delay
• Compatible w/ Electronic & Magnetic Ballasts, CFLs, LEDs, & Incandescents
• Self-Grounding Mounting Strap
• Interchangeable Hot & Load Wires
• No Neutral Required
• No Minimum Load Requirements

The WSD Sensor is a stylish, easy to install, and simple to use Wall Switch Decorator Style Passive Infrared (PIR) sensor. It is ideal for private offices, copy rooms, closets, or any small enclosed space without obstructions. A user programmable time delay ensures that once the room is vacated the sensor will time out and turn off the lights. Additionally, the WSD sensor has several On Modes and Switch Modes that can be programmed using the front push-button. For rooms with obstructions, the Dual Technology WSD PDT Series sensor is recommended. Additionally, all WSD Family sensors have a patent-pending wiring method that enables them to function either with or without a neutral connection. WSD units come pre-configured for wiring without a neutral; however, if connection to neutral is required by code, contractors can convert the unit in seconds. Click Here for programming details

• Auto or Manual On
• PIR Coverage (Passive Infrared)
• Small Motion Detection up to 20 ft, Large Motion Detection up to 36 Ft
• Push-Button Programmable w/o Removing the Switch Plate
• Adjustable Time Delay
• Compatible w/ Electronic & Magnetic Ballasts, CFLs, LEDs, & Incandescents
• Self-Grounding Mounting Strap
• Interchangeable Hot & Load Wires
• No Neutral Required
• No Minimum Load Requirements