• 100-277 V~ forward, reverse, and center phase control input capability
• Provides 0—10 V- control and switching capabilities to switch and dim current sourcing fluorescent ballasts and LED drivers.
• Switches and dims current sourcing 0—10 VDC electronic dimming ballasts/drivers powered by
  100—277 VAC. Switches up to 16 A of electronic capacitive ballasts/drivers.

Solid Ceiling (Drywall, Plaster, Concrete, or Wood)

• Temporary mounting: Ten (10) temporary mounting strips can be purchased in the kit, L-CMDPIRKIT, for temporarily mounting and testing the sensor.
• Permanent mounting: Screws and anchors (for drywall or plaster) provided to mount the sensor.

Recess-Mount:

• Do not recess-mount sensor in a metal surface.
• Recess-mounting ring requires an opening of 3 in (76 mm) in diameter.
• Recess-mounting ring secures internally to ceiling. Sensor twists into the recess mounting ring and sits flush with ceiling.

• Mount the Pico to a pedestal and you have a simple and elegant tabletop control.
• Single, double, and triple pedestals available. Please note that Lutron has discontinued production of the 4-Pedestal option.
• White and black options available

This is the LC&D digilink card. Check out our Acuity products here.

• Gateway to contact closure devices for Acuity LC&D Blue Box and GR  2400 systems
• Able to link 127 digital addresses via Cat. 5 cable
• Up to 14 contact closure inputs
• 6 input to allow digital enable/disable over the bus
• Able to connect to occupancy sensors
• Able to connect to low voltage switches
• Install directly into most panels, option to add separate housing

This is the LC&D GR1400 modem. Check out our Acuity products here.

• Blue Box Modem for connecting to Analog Phone Line
• Attaches into the interior of the Blue Box
• Connect to Phone Line for Dial-in Factory Programming Assistance

This is the LC&D voltage barrier. LC&D voltage barrier separates normal power relays from emergency power relays or different voltages. Check out our Acuity products here.

• For use on BlueBox LT GR1400 Series Panels

The LMLS-MB1 and LMLS-MB2 mounting brackets provide the flexibility to mount the LMLS-400 and LMLS-500 Photosensors to walls, skylight wells or J-Boxes. They are specifically designed to be used in conjunction with these Photosensors.

FEATURES:

• Material: ABS, UL 94 5V Flame Retardant Material
• Indoor Use Only
• Mounting Options:
• LMLS-MB1: 4-Square J-Box / 2-Gang J-Box
• LMLS-MB2: Screw to Wall / Tape to wall with double sided tape

Mounting Considerations:

• Mounting of any RF devices on or in close proximity to a metal surface will drastically reduce the effective range of radio signal transmission or reception.
• All RF devices must be mounted on non-conductive materials to ensure proper performance.
• If you wish to mount your PicoR wireless control to a metal surface, the PICO-MOUNT-1-XX-CPN5733 will be required in order to maintain proper RF performance.

**Stand Alone Mounting Adhesive-Mount (included with Pico® wireless control)

**Screw-Mount (sold separately): Model: PICO-SM-KIT

• Note: Kit includes special screws to be used for more permanent mounting and / or for non-smooth surfaces.

PP and UPP 1 Series Power Packs provide both the 24 V- power supply to operate Lutron® wired occupancy sensors, as well as the 16 A line-voltage relay to control the load, in one compact housing. The unit can be mounted inside a ballast enclosure or inside / outside a junction box. The manual-ON Power Pack (-DV-M) is used to provide a vacancy-only solution (not configurable for occupancy behavior) when paired with Lutron® wired occupancy sensors. A low-voltage momentary switch should be used to manually turn ON the load while the sensor automatically shuts the load OFF when unoccupied. Pressing the momentary switch can also turn the load OFF. The auxiliary Power Pack (-SH) must be used in conjunction with at least one line-voltage Power Pack and one Lutron wired occupancy sensor to switch additional loads.

Features

• High-impact UL94 flammability-rated plastic case construction
• Relay: Class B 266 °F (130 °C) insulating material; silver alloy contacts
• Power Pack units (PP-DV / UPP-DV, PP-347H, PP-DV-M / UPP-DV-M) power up to 3 total devices. PP-SH / UPP-SH counts as 1 device; each occupancy sensor counts as 1 device.
• For indoor use only, 32 °F to 104 °F (0 °C to 40 °C), 0% to 90% humidity, non-condensing

Power packs are the heart of the low voltage sensor system. A PP20 Series power pack transforms
Class I high voltage (120/277 VAC or 347 VAC) to Class 2 15 VDC for powering remote sensors. The
PP20 and the SP20 Series slave pack are also capable of switching lighting loads on and off using
their internal relays. Class 2 wire leads connect to 18 to 22 AWG low voltage cable running to the
sensors, making installation easy and clean. Power packs also have an elongated chase nipple that
allows it to be mounted either directly through a ½ inch knockout into a junction box, or inside an
adjacent box for meeting specific local code requirements in ceiling plenums.
The most versatile power pack is the PP20, which utilizes a patented relay contact protection and
can power up to 14 sensors. Dual-circuit control can be handled by two PP20’s, one PP20 2P Series
2-Pole power pack, or a PP20 power pack and a SP20 slave packs.
FEATURES

•  Powers Low Voltage Sensors (PP20/PP20 2P only)
•  Self-Contained Relay(s) Switch Line Voltage Loads
• Relay Contact Protection
• Plenum Rated