This is the dual technology wall switch sensor w/ 2-relays. The DSW-200 dual technology wall switch sensor turns lights ON and OFF based on occupancy and contains two relays for controlling two independent lighting loads or circuits. It combines the benefits of passive infrared (PIR) and ultrasonic detection technologies for high sensitivity to small and large movements. The DSW-200 replaces existing wall switches and fits a standard decorator wall plate.

Each of the DSW-200’s relays can control a separate lighting load. By default, when the PIR sensor detects occupancy, relay 1 turns ON automatically. Detection by either PIR or ultrasonic technology holds lights ON. When occupancy is no longer detected and the time delay elapses, lights automatically turn OFF. Dual ON/OFF buttons allow the user to turn on and off each of the loads manually. DIP switch settings allow for a variety of control options such as Auto-ON or Manual-ON for each relay, walk-through, and test mode. Check out Wattstopper DLM products here.

This is the RF wall switches. EOSW-100 Series RF Wall Switches work with EOPC-100 wireless occupancy sensors, and optional EORS-100 and EOHR-100 remote switches, to turn lights on and off based on occupancy. Models are available to control one or two switched legs in applications with or without neutral wires at the switch box. Both single and dual relay RF wall switches fit in single gang junction boxes for direct control of one or two loads. Each wall switch can be paired with one or more EOPC-100 wireless sensors for occupancy-based control. By default, single relay wall switches operate in manual-on/automatic-off mode. Dual relay switches are factory set for auto-on to 50%; relay 1 is automatic on/off, and relay 2 is manual-on/automatic-off. When occupancy is no longer detected and the time delay elapses, lights automatically turn off. These sequences of operation, and other default settings, may be changed using hidden configuration buttons. EOSW-100 RF dual relay switches allow for separate pairing of each controlled load (relay) to the integral switch buttons. Additionally, each load may be paired with selected wireless occupancy sensors and selected buttons on RF remote switches. The RF transmission range is approximately 50’ to 150’ depending on product placement. Check out Wattstopper DLM products here.

• RF wall switches work with EOPC-100 wireless occupancy sensors
• Zero-crossing for long relay life
• Choice of manual-on or auto-on operation
• EOSW-111 and EOSW-112 comply with 2011 NEC requirements
• Selectable time delay
• Test mode allows quick and easy set up
• Compatible with decorator wall plates

Wattstopper DW-100 DUAL TECHNOLOGY WALL SWITCH. This is the dual technology wall switch sensor. The DW-100 dual technology wall switch sensor combines the benefits of passive infrared (PIR) and ultrasonic technologies, and can turn lights OFF and ON based on occupancy. It is characterized by high sensitivity to small and large movements, appealing aesthetics, and a variety of features.

The DW-100 fits in a single gang junction box. Once the lights are ON, detection by either technology holds lights ON until occupancy is no longer detected and the time delay elapses. DIP switch settings allow for a variety of control options including Auto-ON operation, walk-through and test mode. By default, Auto-ON turns lighting on when both PIR and ultrasonic technologies detect occupancy. Additional DIP switch settings allow the user to choose which sensing technologies turn ON and hold ON the lighting.

Features

• Complies with 2011 NEC requirements
• Detection Signature Processing eliminates false triggers and
provides immunity to RFI and EMI
• Zero-crossing for long relay life
• Vandal resistant lens combines precise coverage with durability
• Choice of Manual-ON or Auto-ON operation
• Selectable walk-through mode turns lights off three minutes
after the room is initially occupied if no motion is detected
after the first 30 seconds
• Test mode allows quick and easy adjustments
• Selectable audible alert for impending shutoff
• In automatic mode, sensor returns automatically to Auto-ON
after lights are turned off manually; ideal for presentations
• Four occupancy logic options give users the ability to
customize control to meet application needs
• Optional light level sensing with simple setup
• Service mode allows sensor to operate as a service switch in
the unlikely event of a failure
• Sensor coverage tested to NEMA Guide Publication WD 7-2000
• Compatible with decorator wall plates
• BAA/TAA-compliant models available

For other items like the Wattstopper DW-100 DUAL TECHNOLOGY WALL SWITCH click here.

For more information on Wattstopper’s line of lighting solutions click here.

Wattstopper DW-200 DUAL TECHNOLOGY DUAL RELAY WALL SWITCH. This is the dual technology wall switch sensor w/ 2-relays. The DW-200 dual technology wall switch sensor combines the benefits of passive infrared (PIR) and ultrasonic technologies to turn lights ON and OFF based on occupancy. It contains two relays for controlling two independent lighting loads or circuits and a variety of features.

The DW-200 fits in a single gang junction box. Each of the DW-200’s relays can control a separate lighting load. By default, when both PIR and ultrasonic technologies detect occupancy, relay 1 turns ON automatically. Detection by either technology holds lights ON. When occupancy is no longer detected and the time delay elapses, lights automatically turn OFF. Dual ON/OFF buttons allow the user to manually turn on and off each of the loads. DIP switch settings allow for a variety of control options such as Auto-ON or Manual-ON for each relay, walk-through, and test mode.

Features

• Complies with 2011 NEC requirements
• Detection Signature Processing eliminates false triggers and
provides immunity to RFI and EMI
• Zero-crossing on both relays for long relay life
• Vandal resistant lens combines precise coverage with
durability
• Choice of Manual-ON or Auto-ON operation, selectable for
each relay
• Selectable walk-through mode turns lights off three minutes
after the room is initially occupied if no motion is detected
after the first 30 seconds
• Test mode allows quick and easy adjustments
• Selectable audible alert for impending shutoff
• In automatic mode, sensor returns automatically to Auto-ON
after lights are turned off manually; ideal for presentations
• Four occupancy logic options give users the ability to
customize control to meet application needs
• Optional light level sensing with simple setup
• Service mode allows sensor to operate as a service switch in
the unlikely event of a failure
• Sensor coverage tested to NEMA Guide Publication WD 7-2000
• Compatible with decorator wall plates
• BAA/TAA-compliant models available

For other items like the Wattstopper DW-200 DUAL TECHNOLOGY DUAL RELAY WALL SWITCH click here.

For more information on Wattstopper’s line of lighting solutions click here.

WattStopper LMDM 101 DIMMING WALL SWITCH. This is the dimming wall switch. The LMDM-101 Dimming Wall Switch is a low voltage device for dimming control of one or more lighting loads. It is part of a Digital Lighting Management (DLM) system and can dim load(s) connected to DLM dimming room controllers and switch load(s) connected to DLM on/off room controllers. Check out Wattstopper DLM products here.

FEATURES:

• Hidden configuration button for easy access to Push n’ Learn
• Used with DLM dimming room controller
• Digital Lighting Managment components plug together on a free-topology Category 5e DLM local network
• Provides full function dimming control in multi-way applications, such as 3-way, 4-way, and beyond
• Infrared (IR) transceiver for wireless configuration and control
• LED status indicator
• Sleek single gang device fits decorator wall plates
• Six color options and custom engraving options; standard buttons may be replaced in the field
• The product meets the materials restrictions of RoHS
• BAA/TAA-compliant models available

Specifications

Input voltage: 24VDC from DLM local network
• Current consumption: 5mA
• DLM local network connection: 2 RJ45 ports
• Control button with LED status indicator
• 7-LED dimming level indicator
• Hidden configuration button for access to Push n’Learn mode
• Infrared (IR) transceiver
• Operating conditions: for indoor use only; 32-131°F (0-55°C); 5-95% RH, non-condensing
• UL and cUL listed
• FCC part 15 compliant
• Five year warranty

For other items like the WattStopper LMDM 101 DIMMING WALL SWITCH click here.

For more information on WattStopper’s line of lighting control solutions click here.

WattStopper LMPW-100 PIR WALL SWITCH OCCUPANCY SENSORS. LMPW-100 Series PIR Wall Switch Occupancy Sensors use passive infrared (PIR) technology to detect occupancy for energy-efficient control of lighting and plug loads. They also include one or two switch buttons for manual control of selected loads, and are part of a Wattstopper Digital Lighting Management (DLM) system.

Features

• Plug n’ Go™ automatic configuration for quick installation and maximum energy savings
• Push n’ Learn™ functionality for customization without the need for tools or a PC
• Infrared (IR) transceiver for wireless configuration and control
• Sleek single gang devices fit decorator wall plates; 1- and 2-button models; six color options
• Sensors may be used for multi-way control
• Each switch button can control individual or multiple loads, or one scene; LED indicates status
• Each switch button can be used to raise or lower load levels
• Detection Signature Processing eliminates false triggers and provides immunity to RFI and EMI
• Sensor coverage tested to NEMA Guide Publication WD 7-2000
• The product meets the materials restrictions of RoHS

Specifications

• Input voltage: 24VDC from DLM network
• Current consumption: 8mA
• DLM local network connection: 2 RJ45 ports
• 1 or 2 switch buttons, each with LED status indicator
• Scrolling LCD display and pushbuttons for setting sensor and system parameters
• Infrared (IR) transceiver
• Operating conditions: for indoor use only; 32-131°F (0-55°C); 5-95% RH, non-condensing
• UL and cUL listed
• FCC part 15 compliant
• Five year warranty

For other items like the WattStopper LMPW-100 PIR WALL SWITCH OCCUPANCY SENSORS click here.

For more information on WattStopper’s line of lighting control solutions click here.

WattStopper RD-200-W PASSIVE INFRARED (PIR) DIMMING WALL SWITCH VACANCY SENSOR. This is the Passive Infrared (PIR) Dimming Wall Switch Vacancy Sensor. The RD-200 PIR Dimming Wall Switch Vacancy Sensor provides preset dimming control and occupancy-based automatic lighting shutoff for applications throughout the home. The RD-200 can dim incandescent loads from a minimum level of 10% to a maximum level of 100%. When the pushbutton is pressed and held, the RD-200 will ramp the lights up and down in a continuous cycle until the pushbutton is released. The dimming direction may be reversed by momentarily releasing the pushbutton and then pressing it again.

• Replaces standard single pole switch or incandescent dimmer
• Low-profile styling
• Choice of four decorator colors; lens is color matched to device
• Includes matching single-gang wall plate
• Lighted pushbutton for visibility in darkened rooms
• Manual-on or automatic-on operation
• Adjustable time delay from 15 seconds to 30 minutes
• Soft start technology to prolong lamp life
• Air gap isolation switch for safe re-lamping
• If enabled, light level sensing prevents automatic-on when adequate daylight exists

For other items like the WattStopper RD-200-W PASSIVE INFRARED (PIR) DIMMING WALL SWITCH VACANCY SENSOR click here.

For more information on Wattstopper’s line of lighting solutions click here.

CHECK OUT THIS CASE STUDY

WS-CaseStudy-GreenHome_OccupancyVacancyTimeswitches